System-sensor PDRP-1002 Series Manual de usuario Pagina 11
- Pagina / 60
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Options 1. Product Description
PDRP-1002 Instruction Manual PN 51135:B0 04/06/01
11
Remote Annunciator - RZA-4X
The Remote Annunciator mounts on a standard single-gang box, and provides
LED indication of the same functions as the zone relay module. For example,
with DIP switch #1 ‘ON’ and DIP switch #2 ‘OFF’:
• One zone in alarm (red)
• Two zones in alarm (red)
• Releasing Circuit 1 (red)
• Releasing Circuit 2 (red)
• System Trouble (yellow)
A local trouble sounder and silence switch are also provided. All LED wiring
is supervised for open conditions. Any open condition will cause the System
Trouble LED to illuminate. Slide-in paper labels permit an easy change of zone information.
Note: The Remote Annunciator requires the use of an LED Interface Module as described below.
LED Interface Module - 4XLM
The LED Interface Module supports the RZA-4X Remote Annunciator
Module. Annunciator wiring is supervised for open conditions by this module.
The module mounts to the main board on the J8 option connector.
Specifications
Maximum voltage/current, each output: 27.6 V / 8 mA.
Outputs are power-limited.
Meter Module (Volts-Amps) - 4XMM
The Meter Module provides a voltmeter to measure the voltage across the
batteries and an ammeter to measure the charging current to the batteries. The
meters are provided as an assembly that mounts to the lower left-hand corner
of the cabinet.
SYSTEM TROUBLE
RE-SOUND
TONE
SILENCE
FIRE ALARM ANNUNCIATOR
RXA-4XF.cdr
TB1
J2
4XLMF.cdr
0
10 20
30
DC VOLTS
3
DC AMPERES
0
3
4XMMF.cdr
- PDRP-1002 1
- Fire Alarm System Limitations 2
- FCC Warning 3
- Installation Precautions 3
- NFPA Standards 4
- Table of Contents 5
- 1. Product Description 7
- Circuits 8
- Suplemental Documentation 8
- Control Panel 9
- DIP Switch Functions 10
- Remote Annunciator - RZA-4X 11
- LED Interface Module - 4XLM 11
- Specifications 12
- 2. Installation 13
- MS44-cabdim.cdr 14
- MS44-trimring.cdr 14
- ‘AMP’ Jumper 15
- Power Connections 16
- MS44-BATconn.cdr 17
- MRP44-plwiring.cdr 17
- Initiating Device Circuits 18
- MS44-4wiresd.cdr 19
- Output Circuits 20
- Releasing Circuits 21
- Powering External Devices 22
- Optional Modules 23
- Installation - Lower Position 24
- Setup and Configuration 25
- FIRE ALARM ANNUNCIATOR 27
- Setting Mode of Operation 28
- OFF OFF ON ON 29
- OFF ON OFF ON 29
- Power-Up Procedure 31
- 3. System Operation 33
- Control Switches 34
- Zone Status LEDs 34
- Supervisory Service 35
- Zone Disable 35
- Last Event Recall 36
- Non-Silenceable Service 36
- System Events 36
- Brownout Condition 37
- Standby Battery Requirements 39
- FM Approved Releasing Devices 42
- Door Holders, UL Listed 45
- 24 VDC Relays, UL Listed 45
- Minimum System Requirements 47
- Additional Requirements 47
- STD DACT 48
- MS44-411.cdr 49
- Local Energy 50
- Municipal Box 50
- Municipal Box Circuit 50
- 4XTM Transmitter Module 50
- (activated polarities shown) 50
- MS44-rs82.cdr 51
- Maintenance 53
- Troubleshooting 53
- Symptom Problem Solution 54
- Limited Warranty 60
Relacionado con productos y manuales para La Seguridad System-sensor PDRP-1002 Series
(8 paginas)
(1 paginas)König Karty pamięci podręczniki użytkownika
Zaczynanie od C
Comentarios a estos manuales