System-sensor PDRP-1002 Series Manual de usuario

PDRP-1002SeriesAgent Release Control SystemInstruction Manual3825 Ohio AvenueSt. Charles, IL 601741-800-SENSOR2Fax: (630) 377-6495PN 51135:B0

1. Product Description DIP Switch Functions10PDRP-1002 Instruction Manual PN 51135:B0 04/06/01DIP Switch FunctionsThe table below describes the DIP

Options 1. Product DescriptionPDRP-1002 Instruction Manual PN 51135:B0 04/06/0111Remote Annunciator - RZA-4X The Remote Annunciator mounts on a stan

1. Product Description Specifications12PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Specifications AC PowerPDRP-1002: 110/120 VAC, 50/60 Hz, 1.2

PDRP-1002 Instruction Manual PN 51135:B0 04/06/01132. InstallationCabinet MountingCarefully unpack the system and check for shipping damage.Select a

2. Installation Cabinet Mounting14PDRP-1002 Instruction Manual PN 51135:B0 04/06/01The figure below shows the exterior dimensions and mounting hole

Installing Optional Voltmeter/Ammeter 2. InstallationPDRP-1002 Instruction Manual PN 51135:B0 04/06/0115Installing Optional Voltmeter/AmmeterTo moni

2. Installation Power Connections16PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Power ConnectionsWARNING: Do not apply any type power to this c

Power-limited Wiring Requirements 2. InstallationPDRP-1002 Instruction Manual PN 51135:B0 04/06/0117Observe polarity when connecting the batteries.

2. Installation Initiating Device Circuits18PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Initiating Device CircuitsThe control panel provides tw

Initiating Device Circuits 2. InstallationPDRP-1002 Instruction Manual PN 51135:B0 04/06/0119Four-Wire Smoke Detector ConnectionsA maximum of 200mA

LimWarLg.p65 01/10/2000An automatic fire alarm system–typically made up of smokedetectors, heat detectors, manual pull stations, audible warn-ing d

2. Installation Output Circuits20PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Output Circuits Notification Appliance CircuitsThe control panel p

Output Circuits 2. InstallationPDRP-1002 Instruction Manual PN 51135:B0 04/06/0121Releasing CircuitsCAUTION: To prevent accidential discharge, conne

2. Installation Powering External Devices22PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Alarm Relay Circuit One Form-C dry contact alarm relay i

Optional Modules 2. InstallationPDRP-1002 Instruction Manual PN 51135:B0 04/06/0123Optional ModulesOverviewThe control panel has two module connecto

2. Installation Optional Modules24PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Installation - Lower PositionTo install either the 4XTM, 4XZM or

Optional Modules 2. InstallationPDRP-1002 Instruction Manual PN 51135:B0 04/06/0125Setup and ConfigurationTransmitter Module - 4XTMConnect a Remote

2. Installation Optional Modules26PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Zone Relay Module - 4XZMRelay #1 through #4 on this module have s

Optional Modules 2. InstallationPDRP-1002 Instruction Manual PN 51135:B0 04/06/0127LED Interface Module - 4XLMConnect the terminals on TB1 of the LE

2. Installation Setting Mode of Operation28PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Setting Mode of OperationSelect operating mode by settin

Setting Mode of Operation 2. InstallationPDRP-1002 Instruction Manual PN 51135:B0 04/06/0129Switch #2 - Supervisory/Releasing ServiceSet the functio

LimWarLg.p65 01/10/2000WARNING - Several different sources of power can be con-nected to the fire alarm control panel. Disconnect all sourcesof po

2. Installation Setting Mode of Operation30PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Zone Relay Module ConfigurationRelay #1, #2, #3 and #4 o

Power-Up Procedure 2. InstallationPDRP-1002 Instruction Manual PN 51135:B0 04/06/0131Power-Up ProcedureWARNING: Prior to energizing this panel, not

2. Installation Power-Up Procedure32PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Notes

PDRP-1002 Instruction Manual PN 51135:B0 04/06/01333. System OperationWARNING: When used for CO2 releasing applications, observe proper precautions

3. System Operation Control Switches34PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Control Switches Figure 22 Control Panel SwitchesTone Silenc

Piezo 3. System OperationPDRP-1002 Instruction Manual PN 51135:B0 04/06/0135PiezoThe piezo (local buzzer) generates different tone patterns for diff

3. System Operation Last Event Recall36PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Last Event RecallLast Event Recall allows the user to displa

System Events 3. System OperationPDRP-1002 Instruction Manual PN 51135:B0 04/06/0137Single Zone in Alarm (Cross Zone) ConditionUpon actuation of a s

3. System Operation System Events38PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Notes

PDRP-1002 Instruction Manual PN 51135:B0 04/06/0139Appendix A: Secondary Power CalculationsStandby Battery RequirementsThe Standby Battery Current o

NFPA Standards4PDRP-1002 Instruction Manual PN 51135:B0 04/06/01NFPA StandardsThis control panel complies with the following NFPA standards: • NFPA

Appendix A: Secondary Power Calculations Calculating the Battery Capacity40PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Calculating the Battery

PDRP-1002 Instruction Manual PN 51135:B0 04/06/0141Appendix B: Compatible DevicesTwo-wire Smoke Detectors, UL ListedUse the two-wire detectors liste

Appendix B: Compatible Devices Four-wire Smoke Detectors, UL Listed42PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Four-wire Smoke Detectors, UL

Notification Appliances, UL Listed Appendix B: Compatible DevicesPDRP-1002 Instruction Manual PN 51135:B0 04/06/0143Notification Appliances, UL List

Appendix B: Compatible Devices Notification Appliances, UL Listed44PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Table 6 Notification Appliances

Door Holders, UL Listed Appendix B: Compatible DevicesPDRP-1002 Instruction Manual PN 51135:B0 04/06/0145Door Holders, UL ListedUse the Door Holders

Appendix B: Compatible Devices 24 VDC Relays, UL Listed46PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Notes

PDRP-1002 Instruction Manual PN 51135:B0 04/06/0147Appendix C: NFPA Standard-Specific RequirementsMinimum System RequirementsThe control panel has b

Appendix C: NFPA Standard-Specific Requirements Digital Alarm Communicator/Transmitter - Noti-Fire 911AC48PDRP-1002 Instruction Manual PN 51135:B0 0

Universal Digital Alarm Communicator - 411UDAC Appendix C: NFPA Standard-Specific RequirementsPDRP-1002 Instruction Manual PN 51135:B0 04/06/0149Uni

Table of ContentsPDRP-1002 Instruction Manual PN 51135:B0 04/06/015Table of ContentsNFPA Standards...

Appendix C: NFPA Standard-Specific Requirements Local Energy Municipal Box50PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Local Energy Municipal

Remote Station Receiver - RS82-9 Appendix C: NFPA Standard-Specific RequirementsPDRP-1002 Instruction Manual PN 51135:B0 04/06/0151Remote Station Re

Appendix C: NFPA Standard-Specific Requirements Remote Station Receiver - RS82-952PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Notes

PDRP-1002 Instruction Manual PN 51135:B0 04/06/0153Appendix D: Testing & MaintenanceTestingInspectionPerform the following prior to applying pow

Appendix D: Testing & Maintenance Troubleshooting54PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Table 9 Troubleshooting Table Symptom Pro

IndexPDRP-1002 Instruction Manual PN 51135:B0 04/06/0155IndexNumerics110/120 VAC 12220/240 VAC 12411UDAC 47, 494XLM LED Interface Module 11, 234XMM

Index56PDRP-1002 Instruction Manual PN 51135:B0 04/06/01GGeneral Alarm 30ground fault 33, 50IIndicating Circuit #1 53initial alarm test 53initiating

IndexPDRP-1002 Instruction Manual PN 51135:B0 04/06/0157Rrail 24rail, backbox 13, 14red wire 17regulated power 22relay contacts 49Relay, System Alar

58PDRP-1002 Instruction Manual PN 51135:B0 04/06/01

PDRP-1002 Instruction Manual PN 51135:B0 04/06/0159

Table of Contents6PDRP-1002 Instruction Manual PN 51135:B0 04/06/01Zone Relay Module - 4XZM ...

Limited WarrantySystem Sensor® warrants its products to be free from defects in materials and workman-ship for eighteen (18) months from the date of

PDRP-1002 Instruction Manual PN 51135:B0 04/06/0171. Product DescriptionOverviewThe PDRP-1002 Agent Release Control System has been designed as a co

1. Product Description Circuits8PDRP-1002 Instruction Manual PN 51135:B0 04/06/01CircuitsInput CircuitsDetector Zone 1 (Style B/D)Detector Zone 2 (S

Control Panel 1. Product DescriptionPDRP-1002 Instruction Manual PN 51135:B0 04/06/019Control Panel Figure 1 Control PanelSW1TB1TB2TB3TB4JP1GENALM