System-sensor 2100AT Manual de usuario descargar pdf

D200-69-00 1 I56-1145-05R

2100AT Photoelectronic

Smoke Detector with Fixed Heat

and Integral Temp-3 Sounder

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

Specifications

Diameter: 5.5 inches (140 mm)

Height (including mounting bracket): 2.05 inches (52 mm)

Weight: 7.5 oz. (210 g)

Operating Temperature Range 32° to 100°F (0° to 38°C)

Operating Humidity Range: 10% to 93% Relative Humidity, Noncondensing

Latching Alarm: Reset by momentary power interruption

Audible Signal: 85 dBA minimum when in alarm or with supply polarity reversed

Heat Sensor: 135°F Fixed Temperature Electronic Thermistor

Electrical Ratings

System Voltage (nominal): 12 or 24 VDC

Minimum: 8.5 VDC

Maximum: 35 VDC

Maximum Ripple Voltage: 30% of nom. Voltage (peak to peak)

Standby Current: 50

A average, 100

A maximum

Alarm Ratings: 29 mA typical at 12 VDC, 63 mA typical at 24 VDC, 100 mA maximum

(If used, the RA400Z Remote Annunciator operates within the specified detector

alarm currents.)

Reset Voltage: 1.8 VDC minimum

Reset Time: 0.6 seconds maximum

Start-up Time: 30 seconds maximum (after 60 sec. reset)

EOL Relay: A77-716B, 12/24 VDC

Special Considerations: NOTE: Only one detector per zone shall be used, unless when in alarm the panel

switches the zone to a reverse polarity, non-current limited power supply. For

panels that do not provide this feature, a reversing relay, such as System Sensor’s

RR-2, may be used. When utilized with the 2100AT, it allows for more than one de-

tector to be utilized on a loop. Some panels may require the use of programmable

outputs. Refer to System Sensor literature for further information on the RR-2.

The 2100AT detector shall not be mixed with other 2-wire detectors on the same

zone.

–Due to the built-in temporal pattern, use this detector only with a non-coded

power source.

Figure 1. Wiring diagram for the 2100AT detector:

A78-2336-15

IMPORTANT: OBSERVE POLARITY

Polarity must be observed on the power and remote annunciator connections.

OPTIONAL CLASS A WIRING

EOL

INITIATING

LOOP

UL LISTED

COMPATIBLE

CONTROL

PANEL

–

RA400Z

REMOTE

ANNUNCIATOR

–

NOT

USED

NOTE: Only one detector per zone shall be used, unless when in alarm the panel switches

the zone to a reverse polarity, noncurrent-limited power supply. The 2100AT

detector shall not be mixed with other 2-wire detector types on the same zone.

1 2 3 4

Indice de contenidos

Pagina 1 - 2100AT Photoelectronic

D200-69-00 1 I56-1145-05R2100AT PhotoelectronicSmoke Detector with Fixed Heatand Integral Temp-3 SounderINSTALLATION AND MAINTENANCE INSTRUCTIONS 3825

Pagina 2 - D200-69-00 2 I56-1145-05R

D200-69-00 2 I56-1145-05RTAMPER SLOT(DEPRESS TAB TOREMOVE DETECTOR)TAMPER RESISTANT TAB (CUT OFF SMALL TAB TO ACTIVATE TAMPER-RESIST FEATURE)ALIGNMENT

Pagina 3 - D200-69-00 3 I56-1145-05R

D200-69-00 3 I56-1145-05RSystem Sensor smoke detectors are marked with a compat-ible identifier located as the last digit of a five digit codestamped

Pagina 4 - A78-2565-05